منزل •asphalt paver specifications

asphalt paver specifications

  • HANOVER GUIDELINE SPECIFICATION Paving and Surfacing ...

    Neoprene-Modified Asphalt Adhesive Under Asphalt Block: MASTIC (Asphalt Adhesive) HANOVER ® GUIDELINE SPECIFICATION Paving and Surfacing Asphalt Block PAGE 1 Asphalt Solvent Fiber Mineral Filler Amine Salt Clay Latex % 49-53 17-22 3-5 8-11 1-2 7-9 7-13 CAS 6 3 TLV 5mg/m3 ...

  • CITY OF FARGO SPECIFICATIONS ASPHALT PAVING

    AASHTO MP1. The asphalt cement shall be PG 58-28 unless otherwise specified. 2.2. TACK COAT The tack coat shall meet the requirements of ASTM D977 or ASTM D2397 and be emulsified asphalt, SS-1H; an asphalt cutback, RC-250; or asphalt cement, 120-150 Penn. grade. The tack coat to be used on any job shall be subject to the approval of the Engineer.

  • Asphalt Pavement Construction - Asphalt Institute

    Most equipment manufacturers will give a suggested maximum speed for their paver. A lot of agency specifications will specify a maximum speed, such as 30 or 40 feet per minute. Most compaction manufacturers recommend a maximum roller speed of 3 mph and most often more than one roller pass is needed to get compaction.

  • SECTION 32 12 16, ASPHALT PAVING - Veterans Affairs

    The Asphalt Concrete Paving equipment, weather limitations, jobmix formula, mixing, construction methods, compaction, finishing, tolerance, and protection shall conform to the requirements of the appropriate sections of the State Highway Specifications for the type of material specified.

  • SECTION 02513 ASPHALT CONCRETE PAVING

    ASPHALT CONCRETE PAVING STD SPEC 02743 - 2 PART 2 - MATERIALS 2.01 ASPHALT CONCRETE PAVING Asphalt concrete paving shall conform to III-C2-AR-4000 as listed in Section 400-4 of the Public Works Specifications "GREENBOOK." 2.02 ASPHALT Asphalt shall be viscosity grade AR 4000 or AR 8000. Asphalt content in the pavement shall be 5.5% to 6.0%.

  • Construction Guide Specification for Microsurfacing

    Apply a tack coat, if required by the Agency, using an emulsified asphalt (an SS, CSS, or micro surfacing grade) meeting the requirements of M 140, M 208, or M 316. Dilute the emulsified asphalt one-part emulsified asphalt to one to three-part(s) water at the emulsified asphalt supplier's facility or the project site as approved by the engineer.

  • AP1000D Asphalt Paver Specs & Dimensions

    In our specifications database, you will find engine, weights, drive system hopper and service refill capacities specs of asphalt pavers. Through the Heavy Haulers specifications database, you can compare asphalt paver specs with similar models from other manufacturers until you get the most suitable one.

  • BID PACKAGE AND SPECIFICATIONS FOR ASPHALT PAVING …

    2.03 All asphalt wearing surface shall be TDOT 411-02.01 mineral aggregate for Asphalt Concrete Surface Grading "E" with TDOT 411-02.02 Asphalt Cement for Asphalt Concrete Surface Grade E. 2.04 Reference Specifications: Tennessee Department of Transportation; Roadway and Bridge Specifications, Latest Revision; 1.

  • DIVISION 400 PAVEMENTS

    401.10 Asphalt Pavers. Self-propelled asphalt pavers shall be provided and equipped with an activated screed assembly, heated if necessary, capable of spreading and finishing the asphalt plant mix material in lane widths applicable to the typical section and thicknesses shown in the Contract. Pavers used for

  • (PDF) Sustainability of Asphalt Paving Materials ...

    2. Experimental Work 2.1 Materials 2.1.1 Asphalt Cement One type of asphalt was employed in this study which is (40-50) penetration grade obtained from Nasiyraa refinery. The asphalt characterizations were evaluated according to ASTM standard [21], and compared with Iraqi specification know as State Corporation for Roads and Bridge [22] .

  • Carlson CP130 Commercial Class Asphalt Paver - Astec

    Featuring a 130hp (97kW) Cummins® Tier IV Final engine, heavy-duty wear components and class-exclusive armrest controls, the CP130 is paired with the EZCSS single slide 8'-15' screed, combining Carlson's legendary extension support system and award-winning paving performance of its highway-class models into a commercial class platform. 2:20.

  • Specification Databases - Asphalt Institute

    Serving the needs of liquid asphalt manufacturers and suppliers worldwide since 1919. 2696 Research Park Drive Lexington, KY 40511-8480. Freephone: +1 866 540 9577 Telephone: +1 …

  • Asphalt - FDOT

    State Construction Pavement Engineer - Rich Hewitt (386) 943-5305. Research Topics. Developmental Specifications (link to Program Management) ; Resources. Specification Information. Asphalt Quick Reference (For Contracts Let after Jan. 2011) (*.pdf, 395kb); LS/DB Asphalt Pay Adjustment System (*.pptx, 68kb) Updated 2/22/17; QCRR - Calculating Engineer Approved Changes …

  • 32 12 16 - Asphalt Paving

    ASPHALT PAVING RELEASE - 2.0 SECTION 32 12 16 BART FACILITIES STANDARDS Issued: 09/30/2008 STANDARD SPECIFICATIONS 3.03 SEAL COAT A. Apply seal coat over finished paving surface in conformance with Section 37 of the Caltrans

  • STANDARD CONSTRUCTION SPECIFICATIONS FOR ASPHALT …

    to make check tests of the asphalt received on the Project site, and if the asphalt is not in accordance with the certified analysis, he may reject the material. The asphalt required by these Specifications shall conform to the requirements of The Asphalt Institute for the type and grade shown below: Asphalt for Seal Coating CRS-2 or CRS-2P

  • MASTER SPECIFICATIONS Division 32 EXTERIOR …

    ASPHALT PAVING 32 1216 - 1 SECTION 32 1216 – ASPHALT PAVING . PART 1 - GENERAL . 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections, apply to this section. B. Comply with most current edition of the Northwestern University Design ...

  • Asphalt Paving Machines: Screeds & Asphalt Pavers | ...

    Asphalt Paving Machines offers a broad range of asphalt paving equipment that competes in the rubber tire, steel track and rubber belted markets. Pavers and windrow elevators provide versatile and reliable solutions to demanding paving applications.

  • (2360) PLANT MIXED ASPHALT PAVEMENT February 4, 2011 …

    Page 3 of 40 If adding a liquid anti-strip additive to the asphalt binder, complete blending before mixing the asphalt binder with the aggregate. Only use liquid anti-strip additives that ensure the asphalt binder meets the Performance Grade (PG) requirements in 3151. The Contractor may use asphalt binder with liquid anti-strip added

  • Asphalt Paving Design Guide - APAO

    The Asphalt Pavement Association of Oregon is a non-profit trade association representing contractors and associated firms. APAO was formed in 1969 by a small group of asphalt paving contractors to develop improved specifications and products. The Association and its members are dedicated to promoting asphalt pavements by developing pro-

  • P5320B ABG | Asphalt Pavers | Overview | ...

    Achieve the ultimate in paving operations with 's P5320B ABG tracked paver, delivering outstanding performance, durability and ease of operation in paving widths of up to seven meters. With decades of ABG paving technology plus an extensive service network, the P5320B offers market-leading paving quality, ensuring maximum uptime and profitability of your investment.

  • Typical Specifications | Pavingexpert

    Feel free to copy and paste these typical specifications into your own documents. Block Paving Works Concrete Block Paving. This specification is suitable for most residential projects such as patios and driveways. Excavate to reduced depth of at least 200mm below finished level (350mm below dpc) and cart all spoil to licensed, off-site tip.

  • HOT MIX ASPHALT PAVEMENT DESIGN GUIDE

    still hot.(Hot mix asphalt may be placed by hand when it is impractical to use a paver.) Asphalt pavements are constructed of one or more courses of hot mix asphalt placed directly on the subgrade or on a subbase. HOT MIX ASPHALT SPECIFICATIONS All work …

  • Asphalt Paving Specifications

    Asphalt Paving Specifications . 1. General Description These specifications cover the requirements for the construction of Superpave Asphalt Pavement Material (APM). They include the general requirements for the construction of one or more lifts of on a prepared APM surface. The work shall consist of the preparation of the meeting the ...

  • SPECIFICATIONS - co-asphalt.com

    SECTION 401 REVISIONS. Compaction of Asphalt - Revision of Section 401. Compaction Pavement Test Section Revision of Section 401. Binder Replacement - Revision of Section 401.02 (b) Composition of Mixtures – Voids Acceptance Revision of Section 401cmva. Plant …

  • Specifications 8500 Series Asphalt Pavers

    Specifications 8500 Low Deck Contact your LeeBoy dealer: LeeBoy has designed and manufactured superior asphalt paving and grading products since 1964. The LeeBoy brand is well-known for its quality and innovative design. This standard of quality provides contractors with dependable, low maintenance

  • BARBER GREENE Heavy Equipment Specifications and Brochures

    BARBER GREENE Heavy Equipment Specifications and Brochures. Show: 5 10 15 20 25 30 50 100 All. Sort By: Product Name (A - Z) Product Name (Z - A) Product Model (A - Z) Product Model (Z - A) Product Price (Low > High) Product Price (High > Low) BG-200A. Barber Greene Asphalt Pavers. BG-210. Barber Greene Asphalt Pavers.

  • Cold Mix Asphalt Paving Specifications | Career Trend

    Cold mix asphalt is used as a road patch and crack filling material. It offers advantages over hot mix asphalt because it does not require expensive rollers and tampers and can be used year round. Some products are better than others for hot or cold climates and for those climates with varying degrees of moisture and ...