منزل •polaris snowmobile crankcase sealant

polaris snowmobile crankcase sealant

  • crank case sealant | SnoWest Forums

    crank case sealant | SnoWest. I've received emails and PM's asking me about "Group Buys" and promotions. A Group Buy here on SnoWestOnline.com would be a situation where a normal member (non vendor or mfg) personally collects orders from other members. That member then uses those orders to negotiate a better price with the Vendor/Mfg for HIS ...

  • Mag Crank Seal Leaking? | SnoWest Forums

    8. Roberts, MT. Dec 27, 2019. #1. Hey guys, Looking over my sled after our last ride and noticed some oil on the mag side of the engine case of my pull rope cover. Is this something I should worry about, like a crank seal leaking, or can this be normal? Engine only has about 500 miles on it. J.

  • crankcase sealant ? | Hardcore Sledder

    1,931 Posts. #9 · Feb 18, 2008. When I sent my crank out to have the bearings done, the guy said he was going to use Loctite 518 or 519. It's that red jelly like stuff. I know that guy really knows his stuff, because he used to actually work for Polaris, tought some of their tech schools and has done cranks since before I was born...

  • xlt 600 crank seal question | Snowmobile Fanatics

    Discussion Starter · #1 · Sep 20, 2008. I just got a 1997 indy xlt 600. There is an oil leak at the crank on the clutch side. I sprayed the area with starter fluid at idle and there was a very subtle change in the rpm. No oher areas seem to be leaking. I know I have to split the case to replace the crank end seal.

  • Crankcase sealant | Snowmobile Fanatics

    Joined Mar 18, 2005. ·. 5,400 Posts. #5 · Apr 25, 2006. Just go through the deal, they'll get the right stuff. I know Ski-Doo prefers the loctite stuff. Polaris likes to use the 3-bond stuff and permatex is just a cheap version of both of them. T.

  • Signs of a bad crank seal? | Snowmobile Fanatics

    Joined Mar 6, 2010. ·. 46 Posts. #6 · Apr 11, 2010. If the crank seal goes it will cause a lean condition on that side. Fouled plug says you are getting too much fuel. If the fuel pump diaphram goes it usually causes fuel to fill the crank through the impulse line. I believe on the 400 that the impulse runs off of the pto side.

  • Crank seal leaking | Snowmobile Fanatics

    Joined Oct 5, 2002. ·. 608 Posts. #5 · Jan 22, 2008. To do it correctly it must be pulled out and split the crankcase halves. You can leave the cylinders and heads on. Some firmly believe that you can just pull the old seal out and press the new one in but don't try it. 7.

  • Crank Case Sealant....What to use? | Snowmobile Fanatics

    2,592 Posts. #4 · Apr 26, 2005. I went to checker auto or whatever its called in other states. Went down the section of sealants and picked up some. It was a small engines crankcase sealant. Said for snowmobiles, atv's, dirtbikes, etc. Thats what I used on my xlt and its seems to be holding up. It was in a grayish tube.

  • how to replace crankshaft seal | Snowmobile Fanatics

    Joined Jul 24, 2001. ·. 47 Posts. #8 · Dec 15, 2006. I have replaced just the seal with no problems.Drill 2 small 1/8" holes in the old seal and use a pick or awl to pop it out.Next fill the inside of the new seal with low temp grease and lightly coat the outside lip with RTV silicone.Start the top edge first so the outside lip fits toward ...

  • : Polaris OEM Crankcase Sealant 5oz 3 Bond 1215 ...

    Choose items to buy together. This item: Polaris OEM Crankcase Sealant 5oz 3 Bond 1215 2871557. $32.99. Only 3 left in stock - order soon. Ships from and sold by Bair's Powersports / Bair's Indian Motorcycle. Polaris Premium Synthetic AGL Plus Gear Lube 32 oz / 946 ml. $22.92.

  • Bad Crank Seal? | Snowmobile World

    Fill the back side of the new seal and using a plastic syringe from a drugstore, or maybe you have a stock of your own inject it into the bearing a well. Clean off as much of the old grease first. You should need about 30-40 ml of grease. Use some sort of seal grease or o-ring oil on the lip of the seal and the crank.

  • Crankcase sealant Question | SnoWest Forums

    1,409. 702. 113. Elko, NV. Feb 7, 2011. #5. The Threebond case sealant is the one you want to use, it is a non-bridging sealant that will allow metal to metal contact. Don't use any anaerobic sealants such as loctite 518, they will seal but you won't get the proper bearing crush as they say.